Product Catalog
Showing 337–352 of 611 results
Under drive motor plate is used to mount the drive motor to the side of the conveyor body extrusion. Plate attaches with included T-nut plate and fasteners. Boss locates the plate into the extrusion T slot. Bearing included for the drive roller shaft. Mounting pattern for 90° gear motor. Should not be used without the AFC-21 Under drive belt cover.
Drive Kit includes all the parts needed to build the conveyor drive except the motor and roller. Includes (1) AFC-18, (1) AFC-19, (1) AFC-20, (1) AFC-21, and (1) AFC-22.
Under drive belt cover – use with the AFC-20 Under drive motor plate to enclose and protect the conveyor belt drive. Solid construction for protection of the drive in industrial use applications.
Timing belt 5mm pitch X 15mm wide timing belt used with the roller and drive pulley to transfer the gear motor drive to the conveyor roller.
Stand Foot Plate attaches to the 3.0” extrusion used on a stand base. Bolt pattern for the extrusion orients at the 45° angle needed. Plate makes a stable base that has provisions for both leveling screws and floor anchor points.
Stand Guide attaches to the bottom of the 1.5” extrusion used in making a stand. This block provides additional lateral support when the extrusion is inside 3.0” stand base extrusion.
Stand Lock Plate attaches to the end of the 3.0” stand base extrusion end tapped holes. The 1.5” adjustable stand extrusion orients at a 45° angle to fit inside the 3.0” extrusion. Included with this plate is the handle kit to lock the adjusting extrusion and easily set the height.
Stand kit without foot includes everything needed except the extrusion to build an adjustable height stand without the foot plate. Extrusions must have the end holes tapped to attach the plates. Included (1) AFC-6, (1) AFC-7, and (1) AFC-7H.
Stand kit with foot includes everything needed except the extrusion to build an adjustable height stand including the foot plate. Extrusions must have the end holes tapped to attach the plates. Included (1) AFC-6, (1) AFC-7, (1) AFC-7H, and (1) AFC-25.
Stand lock handle kit included with the AFC-7 Stand lock plate.
The ball base has a hole pattern to fit most standard T-slot aluminum extrusions. The through hole can be used for routing wires, cables, or small hoses. There is an exit groove out the side of the base for cables, hose, and wires.
This kit includes everything needed to add vacuum to our standard series products. Directly thread in any vacuum cup with a G1/2 fitting or use one of the included adaptors for G3/8 or G1/4 fittings. The supply hose routes back through the knuckles, links, and bases for a clean and reliable solution with no exposed hoses. We also include a special adaptor for mounting decentralized vacuum grippers that have an M8 stud. The side port allows the pressure supply to run internally and the only exposed hose is at the gripper.
This adaptor plate mounts to the robot and to aluminum 1.5” and 1.0” series extrusions either vertically or horizontally. This plate can also mount (2)
or (4) AFSB-1000-10-V vacuum arms directly onto
the plate instead of using the aluminum extrusion.
This kit adds a knuckle and a ball base to the AFSB-10-V for a great start to building your vacuum gripper. By adding links and knuckles, this kit can be extended to fit most any need. Includes (1) AFSB-10-V Vacuum Kit, (1) AFSB-1 base, (1) AFSB-2 knuckle.
This single arm Standard Series kit with a 12” link is ready to mount any standard series mounting plate. This kit includes: (2) AFSB-1 bases, (2) AFSB-2 knuckles, (1) AFSB-3-12 link, and (1) AFSB-Clamp Handle.
This single arm Standard Series kit with a 2” link is ready to mount any standard series mounting plate. This kit includes: (2) AFSB-1 bases, (2) AFSB-2 knuckles, (1) AFSB-3-2 link, and (1) AFSB-Clamp Handle.
+65 6748 5517
info@jm-vistec.com
10 Kaki Bukit Ave 1, #07-06, Singapore 417942
